The blue section describes the new Webinaris version
If you have a dark gray menu on the left in your Webinaris account, you have the new version.
Click HERE to go to the section for the old version.
Click HERE for more information on the Webinaris versions.
If you have a dark gray menu on the left in your Webinaris account, you have the new version.
Click HERE to go to the section for the old version.
Click HERE for more information on the Webinaris versions.
There is not yet any content for the new version.
Please contact our support team at info@webinaris.com - we are happy to helpy you!
Please contact our support team at info@webinaris.com - we are happy to helpy you!
The yellow section describes the old Webinaris version
If you have a blue bar at the top of your Webinaris account, you have it old version.
Click HERE to go to the section for the new version.
Click HERE for more information on the Webinaris versions.
If you have a blue bar at the top of your Webinaris account, you have it old version.
Click HERE to go to the section for the new version.
Click HERE for more information on the Webinaris versions.
I) Introduction
With our HTTP Universal Interface, you can connect to all third-party tools that have an incoming API based on HTTP GET or HTTP POST. Experience has shown that the interface can be used to connect the following third-party tools:
Your provider is not listed? Then send us an e-mail to info@webinaris.com and we will be happy to check to what extent a connection can take place.
II) Setup at Webinaris
With the HTTP Universal Interface, you can enter HTTP GET and HTTP POST calls in Webinaris, which are executed in the background at certain times and according to certain criteria. For example, you can trigger the transmission of the access data via Optivo Broadmail when you register, or 10 minutes after the webinar you can send Worldsoft the information which participant participated in the webinar and which participant did not.
The procedure is always the same. Only the content to be entered differs. Please refer to the API or interface descriptions of the respective third party provider if we do not yet have a manual.
Proceed as follows to set up the HTTP universal interface:
The procedure is always the same. Only the content to be entered differs. Please refer to the API or interface descriptions of the respective third party provider if we do not yet have a manual.
Proceed as follows to set up the HTTP universal interface:
1. open the "Plugins" menu
2. click on "New Plugin" above
3. click on the HTTP Universal Plugin logo
4. enter the requested data:
- Name: An internal name of the plugin (e.g. name of the third-party tool).
5. click on "Save & Exit".
You can use the plugin you just created in any number of webinar projects.
6. click on "Close" in the upper right corner.
7. Open your webinar project and navigate to the menu "Communication".
8. open the submenu "Interfaces".
9. right click on "+ New interface".
10. select from the list the plugin you have just created
11. on the left side click on "New URL Call".
12. select from the left dropdown menu when and under which conditions the HTTP call should be executed
13. click on the blue "New URL" button to create the HTTP call
14. enter the basic URL of the HTTP call under "URL"
15. for "Method", select whether it is a GET or POST call
16. Click on the plus icon under "Parameters" to add parameters to your call.
These placeholders are available to you:
These placeholders are available to you:
| Placeholder |
Content |
| Webinaris_Vorname |
First name |
| Webinaris_Nachname |
Last name |
| Webinaris_Webinarlink |
Webinar room URL |
| Webinaris_Passwort |
Password for webinar room (no longer required) |
| Webinaris_Login |
E-Mail Address |
| Webinaris_Webinardatum |
Date of the webinar showtime |
| Webinaris_Webinarzeit |
Time of the webinar showtime |
| Webinaris_SourceID |
SourceID |
| Webinaris_Phone |
Phone number |
| Webinaris_Note |
Note |
| Webinaris_UNIXTimestamp |
Date and Time of the webinar showtime in UNIX Timestamp format |
17. click on the "Save" button in the lower right corner to save the changes temporarily
18. click on the "Save" button in the upper right corner to save the settings finally
19. repeat steps 11-17 for each additional HTTP call